-40%

AC Air Compressor Fits For Mazda 3 04-09 Mazda 3 Sport 09 Mazda 5 06-10 57463

$ 54.9

Availability: 659 in stock
  • Returns Accepted: Returns Accepted
  • Brand: Yitamotor
  • Return shipping will be paid by: Seller
  • Refund will be given as: Money back or replacement (buyer's choice)
  • Condition: New
  • Interchange Part Number: 140162C,140639C,
  • Warranty: 1 Year
  • Placement on Vehicle: Front
  • Manufacturer Part Number: F09OG1916
  • Other Part Number: 50523,C1436,10348310,1010759,1110759,1210759,5511699,7511699
  • Fitment: for Mazda 3 04-09 Mazda 3 Sport 09 Mazda 5 06-10
  • Pre-filled Oil: 100ml
  • Item must be returned within: 30 Days

    Description

    Document
    NOTE: Each AC air compressor comes with 100ML of Oil. You dont need to add oil additionally.
    Fit For:
    2004-2009 for Mazda 3 2.0L
    2004-2009 for Mazda 3 2.3L
    2006-2010 for Mazda 5 2.3L
    2009 for Mazda 3 SPORT 2.0L
    Interchange Part Number:
    140162C,140639C,50523,C1436,10348310,1010759,1110759,1210759,5511699,7511699
    Other Part Number:
    25715.5T1NEW, 25715.5T1, 2403-423262, 0610104  KT1347, 11157463, 14-0639C, 10362700, 58463 57463
    Installation Method
    Attention Please:
    Be sure to clean the air conditioning system before installation, otherwise it will cause compression broken.
    1.
    Remove compressor:
    Remove the A/C belt from the A/C compressor pulley. May involve loosening the belt tensioner (if equipped).
    2.receiver drier or accumulator, orifice tube or expansion valve.
    3.Disconnect the negative battery cable.
    4.Remove the bolt that secures refrigerant lines to the A/C compressor. Inspect A/C lines for any contamination such as metal or excessive dirt inside of them. If you find any contamination the system will need to be cleaned.Flush the condenser and evaporator using NON-OIL BASED A/C flush. On expansion valve systems. The valve must be removed before the  evaporator can be flushed. Flushed condensers from outlet to inlet and evaporators from inlet to outlet.
    5.Drain all the oil from the new compressor ,if you compressor has a drain plug you will need to open it up and drain what oil is in there too.
    6.Install half oil charge into the compressor and the remainder throughout the system. Turn compressor shaft 8-10 full revolutions to insure front seal and other internal parts are lubricated.
    7.Install new receiver drier or accumulator and new orifice tube or expansion valve.
    8.Evacuate the A/C system for a minimum of one hour.
    9.After evacuation install half the refrigerant charge and let the system set for 1 minute. This will allow the refrigerant to pick up oil and spread more evenly throughout the system.
    10.Turn on the A/C system with the engine running and check to see if cold air is now coming out of the air duct.
    11.If the A/C system is functioning ,you may find that your electric radiator fan and compressor clutch will be cycling off and on depending on the outside air temperature
    Pay attention
    This compressor comes pre-filled with the correct amount of oil. There is no need to add any additional oil to your system.
    Please add 70-80% refrigerant, do not need to fill up
    Noise is generated if too much refrigerant is added
    Package Included:
    1pc A/C Compressor
    (Professional Installer is Highly Recommended )
    WE ACCEPT THESE PAYMENT METHODS
    ( 10% sales tax will be applied for orders shipped to Washington state by state law )
    30 Days easy returns satisfaction guarantee.
    Items to be returned must be in original factory condition.
    Please enclose a note about item number and order id, your eBay ID and the reason of return.